Re[3]: vytlac si doma zbran na 3D tlaciarni aj ty... :: Remember, remember, the velvet November


node:	Re[3]: vytlac si doma zbran na 3D tlaciarni aj ty...
template:	4
parent:	Re[2]: vytlac si doma zbran na 3D tlaciarni aj ty...
owner:	ntn
viewed by:
created:	11.12.2012 - 09:08:29

cwbe coordinatez:
101
63533
2129387
6955978
6955997
6956050
6962214

ABSOLUT
KYBERIA

permissions
you:	r,
system:	public
net:	yes

IMHO toto nie je vacsie ohrozenie ako clovek s prakom. Dostrel rovnaky, presnost takisto. Len tato 3d zbran IMHO nevydrzi viac ako 1 vystrel.

0000010100063533021293870695597806955997069560500696221406962597

Tri veci:
1. Tato zbran vydrazala viac ako jeden vystrel.

2. Povodna AR-15 ma dostrel cca 500 metrov, tato plastova nech by mala efektivny dostrel hoc 100 metrov, myslim, ze to bude viac nez dokazes "efektivne dostrelit" s prakom.

3. Mna znepokojuje smerovanie a buduce moznosti, nie dnesny stav technologie.

000001010006353302129387069559780695599706956050069622140696259706964489

Ad. "vygidor": jj, dobre pises, presne pises.

Ad. "ntn": Niet sporu, ale tak hadam to co si pisal je snad (cca) vsetkym jasne. Snad. :-]

000001010006353302129387069559780695599706956050069622140696259706964425

"The problem is that even the strongest 3D-printable thermoplastic currently available for the FDM process (Ultem 9085) doesn't even have half the tensile strength needed to withstand the 24,000 psi maximum allowed chamber pressure of the .22LR round as defined by SAAMI (the Sporting Arms and Manufacturer's Institute).
As such, yes, a 100 percent 3D-printed gun made on a RepRap could certainly go "bang," but even with a barrel of large enough diameter to keep it from exploding, there would be so much deformation in the bore that most of the available energy would be sapped by gas leakage around the projectile (to say nothing of the utter lack of accuracy). In the end, you'd have a smoking, charred crater left for a barrel bore after the single shot."
http://news.cnet.com/8301-11386_3-57499326-76/you-dont-bring-a-3d-printer-to-a-gun-fight-yet/

dostrel ar-15 komp. zbrane je cez 3km (3500+ metrov), to, co spominas je ucinny dostrel na bodovy ciel (point target).
sice neporovnatelne, ale vz.58 (ina raz ako ar-15 komp. zbran, ktoru "tlacili" na tej tlaciarni a ina dlzka hlavne, ktora je pre max. dostrel rozhodujuca) ma ucinny dostrel 600m na bodovy ciel a max. dostrel je cca 2800m a po celej dlzke je smrtiaci.

kazdopadne "amatersky zbrojar" nepotebuje ziadnu 3d tlaciaren, staci mu hornbach, baumax ci iny dodavatel a dielnicka s nastrojmi pre rucne a strojove opracovanie kovov ;)

000001010006353302129387069559780695599706956050069622140696259706962661

Nie nie nie, vystrely mozu byt akekolvek, plastova hlaven proste neznesie ani ten tlak ani opotrebenie. Prvy vystrel ju zmeni na nepoznanie a bude IMHO prakticky nepouzitelna. Druha vec je ze pri vystrele sa projektil urcite neroztoci, co je potrebne pre dostrel aj presnost.

PS: buducnost je zla, s tym suhlasim